One of the most common — and most catastrophic — failures we see on certain Dodge, Ford, and Jeep 4×4s is the complete destruction of the transfer case, often left in multiple pieces along the highway. This failure is violent and devastating to the vehicle when it happens, and it is completely avoidable.

Certain Dodge, Ford, and Jeep 4×4s were equipped with “double cardan” style front driveshaft joints. If you have one of these joints under your truck, it is a ticking time bomb. It is the failure of this double cardan joint that has left an untold number of poor, defenseless transfer cases blown into pieces and left for dead along the lonely highways of America. Fortunately, with a little information and some preventative maintenance, you can save your transfer case from becoming another victim of this villainous u-joint.

Meet the Culprit: The Double Cardan Joint

Double Cardan Joint

The double cardan joint

The double cardan joint is a type of universal joint. Its job is to allow your front driveshaft — which runs from your transfer case to your front differential — to operate properly at a given angle. The design is sound. The problem comes in the form of a lack of maintenance.

Most of the OEM joints that were original to these vehicles were not serviceable — there was no way to grease them. There are aftermarket joints available that are serviceable; however, the vast majority of those go without ever being serviced due to a lack of knowledge or interest in servicing them. And this is what fuels the ticking time bomb.

How the Failure Happens

The aftermath of a seized double cardan joint

After tens of thousands of miles of use in sometimes harsh environmental conditions — think of the brine used to pre-treat roads for winter weather, among other things — and without sufficient lubrication, the double cardan joint eventually seizes, locking up tight and ripping the transfer case it is attached to into pieces.

The carnage doesn’t usually stop with the transfer case. Other victims of this detestable driveshaft can include the transmission, the floorboards, wiring harnesses, and any number of other components — leaving your truck, your baby, your pride and joy, broken and in pieces.

Is Your Truck at Risk?

If your Dodge, Ford, or Jeep uses one of the following transfer cases, then you have one of these monsters lurking under your floorboards:

Here is how to defeat this unseemly u-joint and save your truck from disaster.

How to Defeat It

  1. Replace a high-mileage driveshaft. If you have more than 100,000 miles on your current front driveshaft, change it. Replace it with a new, quality shaft that has a serviceable double cardan joint. The expense of replacing the shaft now far outweighs the expense you’ll be looking at if you experience this type of failure.
  2. Service the new joint. Grease it every 30,000–50,000 miles. A serviceable joint only protects you if it actually gets serviced.
  3. Watch your driveshaft angle. If you have a lift on your truck, make sure the driveshaft angle is not too severe. Operating at an increased angle will cause premature failure of the double cardan joint.
  4. Go easy on the hard launches. If you’ve added horsepower and you enjoy showing people just how much you have from a dead stop, beware. Hard launches can cause even a well-maintained double cardan joint to blow apart.

If you want to play, sometimes you have to pay. This is a part that, if abused, will make you pay. Even a healthy joint has its limits — respect them and it will return the favor.

The Bottom Line

Unfortunately, we’ve seen thousands of NP231, NP241, and NP271/273 transfer cases come into us over the years, broken into pieces. The only thing that causes this type of transfer case destruction is the failure of the double cardan joint.

Heed our warnings and avoid being the next victim of this despicable driveshaft while you still can. We wish you luck in your battle with this deadly u-joint foe, and we’re here to help with any questions you may have. God bless and good luck!

Need a Transfer Case You Can Count On?

If the worst has already happened — or you want to make sure it never does — every remanufactured transfer case from The Gear Shop is fully inspected and matched to your exact vehicle before it ships.

The Gear Shop has been remanufacturing transfer cases since 1945. The information in this article is provided as general guidance for Dodge, Ford, and Jeep 4×4 driveline maintenance. Always consult your vehicle’s owner’s manual for driveshaft and lubrication specifications. Brand names are referenced for identification purposes only.

Platinum No Fault Warranty

36 MONTH / UNLIMITED MILEAGE

The Platinum No Fault Warranty is The Gear Shop’s highest level of coverage and the strongest warranty in the industry. Unlike our Standard Shop Warranty that only covers the part, our Platinum No Fault Warranty also covers your out of pocket expenses — including towing, diagnosis, R&R labor, fluid, rental car, and shipping — for a full 36 months with unlimited mileage. See our warranty page for complete details including limitations.

COVERAGE COMPARISON

Coverage Component Standard Warranty Platinum Warranty
Warranty Term
18 Mo / Unlimited Miles
36 Mo / Unlimited Miles
No Fault Coverage
✗ No
✓ Yes
Replacement Unit
✓ Provided
✓ Provided
Diagnostic Labor
✗ Not covered
✓ Up to $125 (1 hr max)
R&R Labor
✗ Not covered
✓ Up to $125/hr • 5 hr max ($625 max)
Towing
✗ Not covered
✓ Up to $150
Rental Vehicle
✗ Not covered
✓ Up to $70/day • 5 days max ($350 max)
Fluid Replacement
✗ Not covered
✓ Up to $40
Inbound Shipping
✓ Covered
✓ Covered
Outbound Shipping
✓ Covered
✓ Covered

WHAT “NO FAULT” MEANS

If a genuine transfer case failure occurs, we cover it regardless of the cause. Whether the failure resulted from a manufacturing issue or from an installation or operator issue — coverage is authorized as long as a real transfer case failure is confirmed upon inspection.

SINGLE-USE PROVISION

The Platinum Warranty is single-use. After a verified Platinum claim is fulfilled, coverage for the remainder of the 36-month term reverts to our Standard Shop Warranty (parts-only replacement). The warranty term does not reset or extend.

Important: This warranty does not take effect until The Gear Shop has received your qualified return core and original shipping container (or payment of the missing core & container fee). Prior authorization is required before any work is performed, before towing, and before a rental — failure to obtain it results in denial of the claim. The suspected defective unit must first be sent to The Gear Shop for warranty inspection; the replacement unit ships, and reimbursements are issued, only after a genuine transfer case failure is verified. All reimbursements require verified, itemized invoices from licensed businesses open to the public and are subject to the maximums above; submit all reimbursement invoices within 30 days of repair completion. If inspection determines the unit did not fail (misdiagnosis), no coverage of any kind applies and you must repay The Gear Shop’s actual shipping costs within 30 days or this warranty becomes null and void. Coverage applies to the contiguous lower 48 United States only. See the full warranty document for complete terms and conditions.